TM
3
TM
3
LNB-Fernspeisung:
FürdieLNB-Fernspeisungsind3Betriebsartenwählbar:
12V: Alle16ZF-Eingänge(1…16)führen16VoltFernspeisung
(Betriebsart für Quattro LNB)
18V: DievertikalenZF-Eingängeführen14Voltunddie
horizontalenZF-Eingängeführen18Volt
22kHz: WieSchalterstellung18Volt,jedochsinddieHigh-Band
Eingänge mit 22 kHz moduliert (Betriebsart QUAD LNB)
Die Schalterstellung hat keinen Einfluss auf die Steuersignale des Receivers!
DiezutreffendeLNB-FernspeisespannungkannfürdieBetriebsfunktion
„Standby“ oder „Dauerbetrieb“ eingestellt werden.
FürdieLNB-FernspeisespannungstehteinFernspeisestromvoninsgesamt
1600 mA zur Verfügung (maximal 400 mA pro LNB)
Selektive Standby-Funktion:
• DasSystem-BasisgerätverfügtübereineselektiveStandby-Funktion.
Beispiel:
Schauen alle Teilnehmer TV-Programme ausschließlich vom SAT-System A,
wird nur das dafür eingesetzte LNB versorgt. Die interne Logik schaltet die
Versorgungsspannung sowohl zu den übrigen LNBs als auch für die integrier-
ten Verstärker ab. Dieser Vorgang bewirkt eine deutliche Energieeinsparung!
Signalisierung der Standby-Funktion
• DieterrestrischeVerteilungbleibtvonderStandby-Funktionunbeeinflusst.
für SAT-Systeme A B C D
über Stammleitung 1 5 9 13
Hilfsspannung 12 Volt in der gesamten
Kaskade über Stammleitung...
2 6 10 14
Stammleitungsausgänge:
• DemPowerBasisgerätliegen17DC-entkoppelteAbschlusswiderstände
bei. Damit sind die Stammleitungen abzuschließen!
22 kHz 12 V
18 V
22 kHz
18 V
12 V
LNB-Mode
Dauerbetrieb/
Always On
Standby
LNB remote power supply:
3 operation modes can be chosen for the LNB remote power supply:
12V: All16IFinputs(1...16)carry16voltsremotepower
supply (for Quattro LNB).
18V: VerticalIFinputscarry14volts,horizontalIFinputs
carry 18 volts
22 kHz: Same as switch position 18 volts, but the high-band inputs
are 22 kHz modulated (for QUAD LNB)
The switch position does not affect the control signals of the receiver!
The adequate LNB remote power voltage can be set for operation modes
“Standby” or “Always On”.
FortheLNBremotepowersupply,remotepowerof1600mAintotalisavai-
lable (maximum 400 mA per LNB system)
Selective standby function:
• Thelaunchamplifierfeaturesaselectivestandbyfunction.
Example:
If all participants only watch TV programs of SAT system A, only the dedicated
LNB is supplied with power. The internal logic turns off the power supply of all
other LNBs as well as that of the integrated amplifiers. This process saves a
great deal of energy!
Standby function signaling
• Theterrestrialdistributionisnotaffectedbythestandbyfunction.
for SAT system A B C D
via trunkline... 1 5 9 13
Auxiliary voltage 12 volts within
the whole cascade via trunkline...
2 6 10 14
Trunkline outputs:
• Thelaunchamplifierissuppliedwith17DCisolatedterminatingresistors
for terminating the trunkline!
22 kHz 12 V
18 V
22 kHz
18 V
12 V
LNB-Mode
Always On
Standby
Commentaires sur ces manuels